Separate the Reported Rating from What Is Known
A 1,200-amp description gives a buyer an important identifier, but it does not settle what the equipment is or establish its condition. Report the rating as shown in existing records or on an accessible nameplate, and say which source supplied it. If the record says 1,200 amps but a nameplate is unavailable, make that distinction explicit rather than presenting the figure as independently verified.
A rated feeder run may include components that differ by voltage, configuration, or other identifying details. Share any existing nameplate information, including voltage wording, as recorded; do not infer actual system voltage from a rating label or assume every section matches. If voltage is unknown, say so. A reported rating and voltage are identifiers for review, not proof of condition, interchangeability, market value, or acceptance.
Define the Run Without Guessing at Length
Describe the run as a documented feeder busway, then state whether an existing length record covers the whole run, only some portions, or is unavailable. A drawing or schedule may describe a planned route rather than the installed material, so identify the document and its scope where known. If the record gives a total but no section breakdown, retain that limitation instead of dividing the figure into guessed lengths.
Where existing records list individual straight sections, report those entries and their units as written. Distinguish recorded lengths from estimates, and mark any unlisted section length unknown. This matters because a buyer reviewing a long run needs to understand whether the documentation describes the physical inventory or only a route. Sellers do not need to measure, access, or handle equipment to fill gaps; qualified professionals alone should handle electrical equipment.
Keep Straight Sections and Elbows Distinct
Separate the reported count of straight sections from the count of elbows or other changes in direction. If an inventory groups them together, explain that the breakdown is unavailable rather than converting a total piece count into a straight-section count. Existing schedules, photographs, or drawings can help clarify how the run was described, but they may not establish that every listed part remains with the equipment.
Elbows can affect how a run is described even when their individual dimensions or orientation are not recorded. Note any orientation or identification already visible in accessible documentation; otherwise leave it unknown. Do not assume that elbows fit the straight sections merely because the rating or product description appears similar. A review of the specific assets determines what may be purchased, not a seller’s assumption about matching components.
State Which Fittings Are Included
List fittings separately from the main busway when existing records identify them. Depending on the documentation, that may mean noting a count or description of end pieces, tap-off components, hangers, or other fittings, without asserting that any particular item is present. If a record says fittings are included but does not name them, report that wording and its limits. If fittings are not addressed, call their inclusion unknown.
A fitting described as part of the original installation is not necessarily part of the equipment currently offered. Clarify whether the available inventory identifies it as remaining with the busway, records it as removed, or says nothing about its present status. Do not visit or manipulate equipment to check. Existing accessible photographs and records may be shared for review; any uncertain identification should remain qualified rather than being turned into a claim of compatibility or completeness.
Use Documentation and Images Carefully
Useful material can include existing schedules, drawings, inventory sheets, and accessible photographs that show identifying labels or the documented arrangement. Identify each item by source and date if that information is already available, and note when a document is partial or its relationship to the offered run is uncertain. A photo may support identification, but it cannot establish hidden condition, complete inventory, or electrical performance.
No seller testing is necessary, and sellers should not open, energize, isolate, disconnect, move, or otherwise handle equipment to improve a submission. If a detail cannot be confirmed from records already available, label it unknown. Florida Switchgear Buyers reviews the specific equipment and determines whether to make an offer and which assets, if any, are included; a nameplate or photograph does not guarantee acceptance or a particular value.
Describe Scope and Arrange a Review
A concise description can identify the reported 1,200-amp feeder run, the source of that rating, any recorded nameplate voltage, the length records available, and separate counts for straight sections, elbows, and identified fittings. Add a clear note for each missing or uncertain item. This gives the buyer a basis to ask focused questions without requiring the seller to resolve technical unknowns or make claims beyond the documentation.
Florida Switchgear Buyers purchases used, surplus, and decommissioned switchgear and related equipment in all voltage classes, including equipment from decommissioned data centers and closed power plants. It makes cash offers and pays upfront for equipment purchased; for purchased equipment, it handles crane, rigging, disconnects, loading, freight, and hauling. This is equipment purchasing and removal for assets purchased, not a promise of facility demolition or general electrical work. For a review, contact (614) 715-3047 or saleselectricalbuyers@gmail.com.
